| 【实用资料】电动门遥控器使用、匹配、对码方法 |
| 添加时间：2018/1/9 14:07:27 浏览次数： |
| 介绍一下电动门遥控器的使用方法、匹配方法，以及对码方法。 The use of the electric door remote control, the matching method, and the code method are introduced. 工具/原料 Tools / materials 电动门遥控器 Electric door remote control 方法/步骤： Methods / steps: 电动门遥控器的使用方法 The use of electric door remote control A键：按A键是锁定，指纹、门内 开关键停止工作，只有用遥控器才能打开电动门 A key: the A key is locked, the fingerprint, the door open key stop work, only use the remote control to open the electric door B键：按B键是关门，同时也是解（按A键后锁定）锁键 B button: press the B button is closed, but also the solution (press the A key to lock the lock) C键：按C键是开门 C key: press the C key to open the door 电池更换方法： Battery replacement method: 电动门的遥控器在频繁使用下，电池容易出现少电、无电，直接导致电动门的遥控器失灵，从而使电动伸缩门不能正常工作等情况。下面教你如何电动门的遥控器是否少电及更换方法: When the electric door remote controls are used frequently, the battery is prone to be less electricity and no electricity, which directly leads to the failure of the electric door remote controller, so that the electric telescopic door can not work normally. The following will teach you whether the electric door's remote control is less electricity and how to replace it. 1、长按停止键，电动门遥控器上的灯暗或者闪烁、遥控距离变近、遥控器有时失灵等现象，都是因为电池电量不足。需更换电动门的遥控器内的电池 1, long press the stop button, the lights on the electric door remote control are dim or flicker, the remote control distance is closer, the remote control sometimes fails, and so on, all because of the lack of battery power. Batteries that need to be replaced in the remote control of the electric door 2、更换电动门遥控器电池的方法，拧开后盖螺丝，取出电池，型号为1.5V3A，更换新的电池后，试按遥控器上的开门或关门按键，正常后，盖上后盖，拧紧螺丝。 2, replace the electric door remote control battery, screw the rear lid screw and remove the battery. The model is 1.5V3A. After replacing the new battery, try pressing the key on the remote control door or closing the door. After normal, cover the rear cover and tighten the screws. 在开启或关闭电动伸缩门时，如果不是因为遥控距离太短，建议不要拉出电动门遥控器的天线，因为容易对电动伸缩门的遥控器造成损坏，而且容易进水。 When opening or closing the electric telescopic door, if it is not because the remote control distance is too short, it is advised not to pull out the antenna of the electric door remote control, because it is easy to damage the electric telescopic door's remote controller and is easy to water. 电动门遥控器简单拷贝方法： Simple copy method for electric door remote control: 电动门遥控器如何拷贝？确定遥控器完好带电池，还有了解遥控器的发射频率，专业术语叫晶振数值。另外，需要看说明书芯片型号是多少。需要清码和对拷才行，具体的拷贝方法方法如下： How can the electric door remote control be copied? Make sure that the remote control is in good condition with the battery, and the frequency of the remote control is understood. The professional term is called the oscillator value. In addition, you need to see how much the chip is. The need to clear the code and copy it, following the specific method of copying method: 1、清码 1, clear code 双手同时按遥控器锁键和下行建，这时，指示灯会不停的闪动，再松开双手，即为清除成功。那怎么判别遥控器以及清除了呢？只要简单随便按一个键，遥控器指示灯亮一下就熄灭，就表示你操作成功啦。 At the same time according to the remote lock and hands down, then the indicator will stop flashing, then loosen the hands, namely for the removal of success. How do you distinguish the remote control and get rid of it? As long as a single button is simply pressed, the light on the remote control is extinguished, indicating that your operation is successful. 2、对拷 2, copy 拿出之前的遥控器，两个遥控器对准，双手同时按住两个遥控器的开门键，指示灯会快速闪动即为成功。（注意，遥控器最好要接近，就行手机的蓝牙、红外线传输一样，受距离限制），其他三个键的拷贝方法同上，依次进行即可。 Take out the previous remote control, two remote control, both hands and hold two remote controls to open the door key, indicating the flash flash is a success. (note that the best way to control the remote controller is to limit the distance between the Bluetooth and infrared transmission, and the other three keys copy the same way. 电动门遥控器 Electric door remote control 固定码(学习码)电动门遥控器的匹配： Fixed code (learning code) matching of electric gate remote controller: 对拷遥控器的出现，使电动遥控门遥控器的匹配变得非常简单，轻松两步就能快速完成固定码遥控器的匹配。 There's the remote control, remote control, remote control electric door is very simple and easy two steps can be finished quickly, fixed code remote control. (1)特点不需要拷贝机，不需要知道震荡电阻，直接用遥控器来复制遥控器，立马能用。 (1) the character does not need a copy machine, does not need to know the shock resistance, directly uses the remote control to copy the remote control, and it can be used immediately. (2)使用此款遥控器的前提： (2) the premise of using this remote control: ①原遥控器可以用，而且能够正常遥控。 The original remote control can be used, and can be normally remote control. ②需要知道遥控器的频率c例如390MHz，400MHZ等） (2) need to know the frequency of the remote control C, such as 390MHz, 400MHZ, etc. ③遥控器的芯片是以下可拷贝的芯片SC2260/SC2262/HS2260/HS2262/PT2262/PT2260/EV15271SCL1527/SC5211/FP527/PT2240/HS2260/SC2240/HS1527／CL2262/HS2240/PT2264/LX2260/X2262/LP8527/HX2262/HX2260（市场上大多数固定码和部分学习码遥控器都可兼容） The remote controller chip is the following copy of the SC2260/SC2262/HS2260/HS2262/PT2262/PT2260/EV15271SCL1527/SC5211/FP527/PT2240/HS2260/SC2240/HS1527 / CL2262/HS2240/PT2264/LX2260/X2262/LP8527/HX2262/HX2260 (chip on the market most of the fixed code and part learning code remote control are compatible) (3)具体操作方法 (3) specific operation method ①清码。同时按下遥控器上排的两个按键，"开门"键和"关门"键，指示灯闪一次后约2s后快闪即表示清除成功。清除之后按遥控器4个按键指示灯仅闪一下后熄灭。 A clear code. At the same time, press the two keys of the remote control, "open the door" key and "close the door" key, indicating the light flicker after about 2S after the flash is to indicate the success. After scavenging, the 4 keys of the remote control only flicker and then go out. ②对拷。一个手拿着原装的遥控器，另一个手拿着万能拷贝遥控器，两个遥控器尽量靠近，同时按下两个遥控器"开门"键，拷贝遥控器指示灯快速闪动即表示复制成功，然后再松开您的手。依次按相同方法，将其他三个按键拷贝上去。 The copy. One hand holds the original remote controller. The other hand holds the universal copy remote controller. The two remote controllers approach as close as possible. Meanwhile, press the two remote control "open door" keys, and copy the remote control indicator to flicker quickly, that is to say that the copy is successful, then loosen your hand. Copy the other three keys in the same way. 注意：拷贝时候如果灯不闪动，可以换个位置，比如将两个遥控器的头部对着再拷贝试试。可以多换几个位置试试。 Note: if the light doesn't flicker when copying, you can change the position, for example, try the head of the two remote control in front of the copy. You can try a few more places. ③恢复。若是误操作清除掉有用代码后，在没有重新拷贝其他遥控器之前可同时按下遥控器下排两个按键2s后，指示灯快速闪烁则表示恢复成功。 (3) recovery. If the wrong operation to remove useful code, before re copy other remote control can also press the remote control button two. After 2S, the indicator light flashes quickly said a successful recovery. 对码方法 Code method 1、编码方式 1, encoding method 无线电遥控常用的编码方式有两种类型，即固定码与滚动码两种，滚动码是固定码的升级换代产品，目前凡有保密性要求的场合，都使用滚动编码方式。滚动码编码方式有如下优点： There are two kinds of coding methods for radio remote control, that is, two kinds of fixed codes and rolling codes. Rolling codes are upgrading products of fixed codes. Nowadays, rolling codes are used in all occasions where security requirements are required. The rolling code coding has the following advantages: 1、保密型强，每次发射后自动更换编码，别人不能用侦码器获得地址码； 1. The security is strong. After each launch, the code is replaced automatically. Other people can't use the detector to get the address code. 2、编码容量大，地址码数量大于10万组，使用中重码的概率极小。 2, the coding capacity is large, the number of address codes is more than 100 thousand groups, and the probability of using the medium weight code is very small. 3、对码容易（详见三、配遥控器的方法），滚动码具有学习存储功能，不需动用烙铁，可以在用户现场对码，而且一个接收器可以学入多达个不同的发射器，在使用上具有高度的灵活性； 3, the code is easy (see three, with the remote control method), rolling code has learning and storage function, and does not need to use soldering iron. It can learn many different transmitters on the user site code, and a receiver, and has high flexibility in use. 4、误码小，由于编码上的优势，使得接收器在没有收到本机码时的误动作几乎为0。 4, small error code, due to the advantages of the coding, the receiver in the absence of the local code when the misoperation is almost 0. 固定码编码方式有如下优缺点： The fixed code coding method has the following advantages and disadvantages: 1、固定码的编码容量仅为6561个，重码概率极大； 1, the coding capacity of the fixed code is only 6561, and the probability of heavy code is great. 2、其编码值可以通过焊点连接方式被看出，或是在使用现场用“侦码器”来获取，所以不具有保密性，主要应用于保密性要求较低的场合； 2, its coding value can be seen through the connection of solder joints, or is used in the field with "detector code" to obtain, so it is not confidential, and it is mainly applied to occasions with low security requirements. 3、因为其价格较低所以也 3, because its price is low and so |
| 上一页 电动门的性能特点 |
| 下一页 车库门和车库卷帘门有什么不同 |
Copyright © 技术支持：遨游网络