保定电动门厂-保定电动伸缩门,工业门,车牌识别收费系统

1、  安装之前，一定要保证电动门运行的地面已经用水泥硬化好，并且运行范围内保持水平。

1, before installation, must ensure that the electric door running ground has been hardened with cement, and maintain the level of operation.

2、  电动门的固定一端要铺设好220V/5A的电源。并保证电源能单独控制，具备漏电保护装置。

2, the fixed end of the electric door should be paved with 220V/5A power supply. And ensure the power supply can be controlled separately, with leakage protection device.

具备以上条件，准备好安装用的材料及配件就可以开始安装电动门了。

With the above conditions, ready to install materials and accessories, you can begin to install electric door.

3、电动门的轨道通常为20×20方钢轨道或者为8号预埋轻轨，厂家会根据客户的现场条件为客

3, electric door track is usually 20 x 20 steel rail or No. 8 embedded light rail, the manufacturer will according to the site conditions of customers for the customer

户推荐简便易行的方案。将轨道按说明书的要求标准，安装好轨道。

Recommend a simple and easy program. Track the track according to the specifications and install the track.

4、把电动伸缩门摆放在已经安装好的轨道上，让主机中间的导向轮放在轨道上，把门体调正。

4. The electric retractable door is placed on the track that has been installed, so that the steering wheel in the middle of the main engine is placed on the track, and the door is adjusted.

轨道安装完毕

Track installation completed

5、选择好固定门体尾部的位置，确保伸缩门在中间线的位置，用膨胀螺栓和固定卡把电动

5. Choose the position of the tail of the fixed door to ensure the extension door is in the middle line, and use the expansion bolt and the fixed card to drive the electric

伸缩门门体尾部固定好。

The door of the retractable door is well fixed at the rear.

6、开门限位的安装方法：把门体收缩到一起，要留有一定的活动量，避免门体挤压过紧，

6, the opening limit installation method: the door to shrink together, to keep a certain amount of activity, to avoid the door extrusion too tight,

在开门限位（主机正下方两侧，有标识开门限位或关门限位的磁棒）的垂直正前方平行位置，

The limit at the door (just below the mark on both sides of the host, open or close spacing bar spacing) vertical front parallel position,

用冲击钻打孔，孔的深度及宽度根据厂家提供的磁铁的深度及宽度为准，再放入磁铁，磁铁

Drilling with percussion drilling, the depth and width of the hole shall be based on the depth and width of the magnet provided by the manufacturer, and then put in the magnet and magnet

和地面水平即可，磁铁需露出并平地面，过深将磁铁掩埋则无效。

And the ground level can be, the magnet should be exposed and leveled the ground, too deep to bury the magnet is invalid.

7、关红外线防撞的安装方法：把电动门展开到距离门完全关闭大约1.2米，在防撞限位（主

7 、 infrared ray anti-collision installation method: the electric door is extended to the distance, the door is completely closed about 1.2 meters, in the anti-collision limit (main)

机正下方两侧，有标识关红外的磁棒）的垂直正前方平行位置，用冲击钻打孔，孔的深度及

Just below the two sides of the machine, mark off infrared magnet) vertical front parallel position, punch impact drill, hole depth and

宽度根据厂家提供的磁铁的深度及宽度为准，再放入磁铁，磁铁和地面水平即可，磁铁需

The width is based on the depth and width of the magnet provided by the manufacturer, and then placed in the magnet, the magnet and the ground level

露出并平地面，过深将磁铁掩埋则无效。

Expose and level the ground, but it is invalid to bury the magnet too deep.