SIPOS电动门的调试
Debugging of SIPOS electric door
每天穿梭在发电厂的管道丛林，面对林林总总的电动门，我相信大家都会有了解它的欲望，今天，我们就跟大家简单的介绍一下电动门的调试，当然，不推荐大家去尝试自主调试，这个还是要交给我们专业的热控人员滴，但是，正所谓技多不压身，都学习学习，也是很不错的哦。
The shuttle every day in the power plant pipeline jungle, face numerous electric door, I believe everyone will have the desire to understand it, we just like today, we introduce the debugging, the electric door of course, do not recommend you to try the independent debugging, this is to give our professional thermal control personnel drops. However, the so-called skills are more than body, are learning, is also very good oh.
SIPOS阀门调试
SIPOS valve commissioning
01
01
专业型调试步骤
Professional debug steps
1.1、准备工作。打开信号齿轮单元罩子（方形透明塑料罩），将白色齿轮转到如下位置：
1.1. Prepare for work. Open the cover signal gear unit (square transparent plastic cover), white gear to the following location:
熟悉一下四个按钮的作用：
Be familiar with the role of the four buttons:
接线，上电，确认显示屏有显示。
Wiring, power on, confirm display display.
1.2、调试。
1.2, debug.
（1）进入调试菜单：
(1) enter the debug menu:
按功能键一下或两下，使显示屏第二行显示： locPar，
Press the function key or two, so that the display second lines display: locPar,
按确认键，第一行显示：language setting，
Press the confirmation key, the first line shows: language setting,
按下翻键一下，显示：commissioning，
Press the button to show: commissioning,
按确认键，第一行显示：enter PIN-code，
Press the confirmation key, the first line shows: enter PIN-code,
第二行显示：0000，
The second line shows: 0000,
利用下翻键、上翻键和确认键，使第二行变为：9044，
Using the down, upturn and confirmation keys, the second lines are changed to: 9044,
再按确认键，现在第一行应该显示close direction。
Press the confirmation key again, and now the first line should display close direction.
（2）调试：
(2) debugging:
现在按下翻键，直到第一行显示：enterpos.adjust。
Now press the flip key until the first line is displayed: enterpos.adjust.
按确认键，显示start with pos，第二行显示OPEN，
Press the confirmation key, display the start with POS, and the second line displays the OPEN,
这时我们先调开位（也可以按下翻键选择先调试关位）。
At this time we first switch the bit (also can press the switch key to debug the switch first).
按确认键，显示move to op.pos，
Press the confirmation key, and display move to op.pos,
第二行显示press E-button，按开按钮（即上翻键），
The second line displays the press E-button, press the open button (that is, the upturn key),
现在执行机构应该在朝着开方向运行，显示％open→open，
Now the actuator should run in the direction of%open to open.
这时观察白色信号齿轮的转向（顺时针或逆时针），
The turn of the white signal gear is observed at this time (clockwise or counterclockwise),
运行到全开位置后，执行机构会自动停止，
After running to the full open position, the actuator will stop automatically.
再点按三下关按钮（即按下去接着松开按钮，使执行机构退回一点   点，避免卡死）。
Press three next button (that is, press down and release the button, so that the actuator is returned a little, to avoid the death of the card).
按确认键，第一行显示 adjust of poti，
Press the confirmation key, the first line displays the adjust of Poti,
第二行显示deviation+数值，
The second line displays the deviation+ value,
现在朝刚才观察到的方向转动白色齿轮，
Now turn the white gear in the direction you have just observed.
使数值变小，直到为     0（松开手后也为0才行），
Make the value smaller until 0 (after loosening the hand is 0),
按确认键，显示move to cl.pos，
Press the confirmation key, and display move to cl.pos,
现在按关按钮，是执行机构朝关方向运行直到自动停止，
Now press the button, the actuator runs in the direction until it is stopped automatically.
现在点按三下开按钮，按确认键。显示adjustment ok!，
Now press three to open the button and press the confirmation key. Show adjustment OK!,
证明调试成功。
It is proved that the debugging is successful.
02
02
经济型调试步骤
Economic debug steps
2.1、 拨码开关 介绍
2.1. Introduction of code switch
上图为经济型电动门拨码开关，自左到右依次为S1、S2、S3、 S4、S5、S6、S7、S8。 其中，
The above picture is an economic type of electric gate dial code switch. From left to right, it is S1, S2, S3, S4, S5, S6, S7, S8. Among them,
S1：代表阀门开关方式，即顺时针还是逆时针，默认在下，为顺时针方式；
S1: on behalf of the valve switch mode, clockwise or counter clockwise, by default, clockwise;
S2：关方式，拨下代表力矩关，拨上代表行程关，默认为拨下；
S2: close the way, dial the representative torque, dial on behalf of the trip, the default is to dial down;
S3：开方式，一般为拨上，行程开阀；
S3: open mode, usually dial on, stroke opening valve;
S4、S5、S6可以依据实际情况而定，默认均为拨下；
S4, S5, S6 can be determined according to the actual situation, the default is dialed down;
S7：调试过程中分步确认作用；
S7: Step - by - step validation during debugging;
S8：调试过程第一步、最后一步使用。
S8: the first step and the last step of the debug process.
2.2、电动门调试
2.2, electric door debug
①
1.
S8拨上，如下图
S8 dial up, as follows
接下来开始调节开位置：
Then start to adjust the opening position:
②
2
开门至将近全开，然后逐渐点动开门直至机械位置全开（长按2S之后门会连开）；
Open the door close to full opening, and then gradually open the door until the mechanical position is open (long according to the back door of 2S).
观察H2指示灯，如果红灯闪烁，代表定位器与实际存在偏差，需要调节中心轮，向左或者向右调节，知道H2红灯变灭；
Observe the H2 indicator. If the red light flashes, representing the positioner and the actual deviation, we need to adjust the center wheel, adjust to the left or right, and know that the H2 red light goes off.
③
3
将S7拨上，再拨下，开位保存记忆至芯片内，此时H1、H2交替闪烁； 接下来开始调节关位置：
S7 dial, then dial, open memory memory to the chip, at this time H1, H2 flicker alternately; then start to adjust the position:
④
4.
将下关门，力矩关门自适应，注意观察H2灯，当H2灯闪烁3下后，H1、H2灯开始交替
Turn off the door, turn the moment off and watch the H2 lamp. When the H2 lights flicker 3, the H1 and the H2 lights start alternately
闪烁，代表关位确定；
The scintillation is determined on behalf of the closet.
⑤
5.
将S7拨上，再拨下，保存记忆关位置，此时会出现以下两种情况： A、 H1灯闪烁，H2灯灭，此时代表调试成功；
S7 dial, then dial down, save the memory position, at this time there will be the following two cases: A, H1 lights flicker, H2 lights out, at this time the debug success;
B、 H1灯闪烁，H2灯红灯，代表调试存在错误，需要重新调试，之后需要将S8拨上，再拨下，然
B, H1 lights flicker, H2 light red light, for debugging there is a mistake, need to redebug, after the need to dial S8, then dial down, but
后选择新的齿轮比例，重新从第②开始。 齿轮比例计算公式： 齿轮比例  =  螺距 *  行程
Then choose the new gear ratio and start again from the second. Gear ratio calculation formula: gear ratio = pitch * stroke
⑥
6
将S8拨下，调试完成。
Put S8 down and debug to complete.